SAE AS4201 Port - Ring Locked Fluid Connection Type, 8000 psi Design Standard

作者:标准资料网 时间:2019-04-15 04:23:34   浏览:9479   来源:标准资料网
下载地址: 点击此处下载
Product Code:SAE AS4201
Title:Port - Ring Locked Fluid Connection Type, 8000 psi Design Standard
Issuing Committee:G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
Scope:No scope available.
下载地址: 点击此处下载
MIL-STD-1678/2, DEPARTMENT OF DEFENSE STANDARD PRACTICE: FIBER OPTIC CABLING SYSTEMS REQUIREMENTS AND MEASUREMENTS(PART 2: OPTICAL MEASUREMENTS) (PART 2 OF 5 PARTS) (28 MAY 2010) [SUPERSEDING DOD-STD-1678]., This standard practice provides detailed information and guidance to personnel concerned with ensuring standardization of fiber optic cable topologies (optical fiber cabling and associated components) on military mobile vehicles used in air, land, and sea applications. In general, the requirements and methods specified herein are not identifiable to any specific mobile vehicle class or type, but are intended to standardize and minimize variations in requirements, test setups, test measurement procedures, test sample fabrication configurations, and other aspects that must be addressed for completeness. Where specified, constrains for usage or platform types will be listed. The term 損latform?will be used to refer to the military mobile vehicles in general or, where designated, one particular class (such as 揳ircraft platform? or one particular type within that class (such as 揊-35?.4. In order to provide flexibility in the use and update of the different aspects for requirements and methods, this standard practice is issued in five parts; as follows:Part 1: Design, installation and maintenance requirements. This part addresses design requirements for platforms that use cable harnesses as the means to transport data through optical fiber among communication network and end user equipment. Larger platforms that route trunk cables through cableways and drop cables to the end user (application equipment), can cite applicable requirements in Part 1 of the Standard Practice and augment them with use of MIL-HDBK-2051 and MIL-STD-2042 as appropriate. Surface ships and submarines, are to use MIL-HDBK-2051 and MIL-STD-2042 in lieu of Part 1 of this Standard Practice.Part 2 Optical measurements. Part 2 of this standard practice addresses further details to refine or bound (constrain) the performance of each optical test measurement addressed. The test methods, such as those in a TIA-455 series standard or military standard/specification, are cited already. This part of the standard practice augments the test method in the standard or specification to ensure consistency with setup and measurement procedure. This consistency minimizes variations when comparing data obtained from different test laboratories (including commercial, vendor, Government and Government contractor).Part 3 Physical, mechanical, environmental and material measurements. Part 3 of this standard addresses further details to refine or bound (constrain) the performance of each physical, mechanical, environmental and material test measurement or inspection addressed. The test methods, such as those in a TIA-455 series standard or military standard/specification, are cited already. This part of the standard practice augments the test method to ensure consistency with setup, measurement procedure, data recording/analysis and other factors critical to conducting or evaluating test performance. This consistency minimizes variations when comparing data obtained from different test laboratories (including commercial, vendor, Government and Government contractor).Part 4 Test sample preparation/fabrication requirements. Part 4 of this standard practice addresses further details to refine or bound (constrain) the preparation and fabrication of test samples for the fiber optic components addressed. Fabrication methods, such as those in the Shipboard installation standard, MIL-STD-2042, or in the general series aircraft maintainer抯 manual, NAVAIR 01-1A-505-4/TO 1-1A-14-1, are cited already. This part of the standard practice augments the fabrication method to ensure consistency of the test configurationPart 5 Design phase and legacy measurements. Tests that are more unique to the design phase are addressed in Part 5 of this standard practice. Also, Part 5 addresses some test methods cited in former DOD-STD-1678. The test methods cited in DOD-STD-1678 are considered obsolete; however, a few military specifications and commercial standards still refer to some of the test methods. These test methods are provided in this part of the standard practice with the recommended replacement method. These latter test methods are listed under the constraint that they be used only with the specific military specifications or commercial standards in which they are cited. The intent is to delete each DOD-STD-1678 test method from that standard practice in Part 5 once its reference from military specification or commercial standard is removed.【英文标准名称】:Contractproceduresforbuildingworks-PartC:Generaltechnicalspecificationsforbuildingworks;Joineryworks
【原文标准名称】:建筑工程合同.第C部分:建筑工程通用技术规范.细木工制作工程
【标准号】:DIN18355-2002
【标准状态】:作废
【国别】:德国
【发布日期】:2002-12
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:细木作;性能;会计;施工作业;建筑合同;规范(验收);附加性能;建筑工程承包条例;组件;承包条例;合同;性能规范;建筑工程;建筑;施工材料;设计
【英文主题词】:
【摘要】:
【中国标准分类号】:P02
【国际标准分类号】:91_010_20
【页数】:19P;A4
【正文语种】:德语